Ottoman-Coffee Table from a Wood Pallet

Good snowy afternoon!  Today I’m sharing a project that I actually did a little while ago, but is one of my all-time favorites.  If you’re like me, spending countless minutes, okay hours, pouring over those Pinterest photos of all those awesome projects that are being made from wood pallets, I just had to get in there and try one.  I had been battling with my coffee table for a while any way, so this seemed like the project for me.  I have a little experience with some light upholstery and I own a staple gun, so I was game.  It actually turned out to be quite easy.  The most difficult part was dealing with the cumbersome size of the pallet and working around having to flip it over and center it and such.  I enlisted the help of my daughter who, on occasion, is game to help old mom out with a project or two.

So here are the before and after photos.

pallet ottoman before pallet ottoman 2 pallet ottomanottoman in place

The total cost of the project was about $100 dollars.  The most expensive part was the foam padding.  I was surprised how expensive it was, so if you can find a good source for inexpensive foam, definitely go that route and you can save a lot of money.  The pallet was free.  I got the fabric at Hobby Lobby when their home décor fabric was on sale at 50% off so only spent about $12 for that.  I purchased the legs at Home Depot for about $3 each.  I also bought a package of quilt batting to smooth out the corners and that was about $10 for the size I needed.  So as you can see, the foam was the biggest expense.  If you know of a good source for cheap foam, please do share!  I even got it on a 50% sale at Hancock Fabrics, but it must contain gold 🙂  I am thrilled with it and it has been the best addition to my living room in years.  I have a couple of smaller pallets that I am going to try some more projects with soon as well, now that I got my feet wet.  So stay tuned!

How to Make a Stand Mixer Attachment Holder

mixer attachment in place

I found this project idea while pouring through Pinterest. If you’re like me, those mixer attachments were a constant fight. I would just throw them inside the mixer bowl when not in use, but it always looked cluttered and I had to move them out of the way each time I wanted to use the mixer. But this little miracle idea turned out to be just the trick I needed.

piece of old cutting block All you need to start is a scrap piece of wood. You’ll want something with a flat bottom to it. An old piece of “one by”, old molding or handrail, or anything you have laying in your scrap pile. I had a piece from an old cutting board that I kept hanging on to thinking, “there’s gotta be something I can do with this.” Yes, I must confess, when it comes to those little scraps, I’m a bit of a hoarder. But hey, on this one, I can say I was right, so I feel a little vindicated! (love those small victories)

set on top to measure

mixer option

 

 

 

 

 

 
Next I had to decide if I wanted it upright or flat with my particular piece of wood. I chose upright so that it had a more narrow profile on the counter top.
drill holes and place dowels

 

 

 

You will use a dowel to hold the attachments so choose one that just fits inside the mixer attachments. You want it large enough that the attachments don’t wobble around, but careful that it’s not too big. You want your piece to slide off and on without any struggle. Find your drill bit that matches the size of your dowel. Lay your mixer attachments out on the base piece to determine the proper spacing and make mark where you want to drill your holes. Drill holes about a half inch deep. Put some wood glue into the hole before placing dowel in the hole. You might need a hammer for a little extra tap to get your dowel into the hole if you have a tight fit like I did.

Let dry, and, voila! A cool little storage holder for your attachments. It only took about 30 minutes to make. Feel free to send any questions you may have about this project, and have a great day!
on dowelsin place 2